OneTesla board without kit.

Non-kit projects based on the public Gen1 designs

Re: OneTesla board without kit.

Postby KevinNewZealand » Wed Oct 09, 2013 2:50 pm

I am guessing I could dasiy chain it off the system fan ... then cut a litle hole in the side of the case or even just glue it on the outside of the case without cutting ... would it be over kill to get one for each IGBT / or to find a slightly higher spec gauge that has two probes and can keep an eye on both :) ..
KevinNewZealand
Magnificent MOSFET
 
Posts: 120
Joined: Wed Jul 03, 2013 7:44 pm

Re: OneTesla board without kit.

Postby E.TexasTesla » Wed Oct 09, 2013 10:01 pm

Yes, that's the same temp gauge I purchased from ebay. Mine is wired in with the fan supply.
It could also be powered from the 19v main logic supply.

As far as adding protection circuit to an unmodded onetesla board its going to be tough.
Not alot of room on the board around the IGBTs.

I took a scrap piece of pc board and etched six heavy lines to act as a bridge from the board to the IGBTs.
It gave me alot of room to add a series pair of 1.5KE220 across the emitter and collector of each transistor.
Each 1.5KE220 clamps at around 220 volts so a pair in series across each IGBTs emitter and collector would
clamp down around 440-500 volts. This prevents the IGBTs from going over the 600v rating.
Below the 1.5KE220s are a pair of mur860 diodes which may not be doing any good as I still had failures
after installing them.
Attachments
TV.jpg
(177.32 KiB) Downloaded 425 times
User avatar
E.TexasTesla
Magnificent MOSFET
 
Posts: 163
Joined: Tue Feb 19, 2013 6:07 pm

Re: OneTesla board without kit.

Postby DJKOR » Wed Oct 09, 2013 10:22 pm

If my IGBT's let out the smoke (touch wood, I'm still on my first pair), I'm planning on doing something similar to you where the IGBT's aren't mounted directly on the board (because I have never been a fan of removing components from a PCB more than once). Would you say that the additional modifications you have made do really make a difference with regards to protection or is it more of a "hopefully it is making a difference"? Wouldn't hurt to implement it though in any case right?
Image
My build thread: viewtopic.php?f=15&t=998 | 246kHz Primary / 267kHz Secondary
User avatar
DJKOR
Magnificent MOSFET
 
Posts: 193
Joined: Sat Aug 17, 2013 4:12 am
Location: Brisbane, QLD

Re: OneTesla board without kit.

Postby KevinNewZealand » Thu Oct 10, 2013 4:13 am

indeed, the most challenging aspect for me so far has been the " reworking" required when things go bad , in fact if I had not had backwards LEDS , I think I would have had this baby up and running a month ago :) , my bad skills at rework stage are the source of my dead IGBTS and dead diodes ...

I wonder if some people with more experience than me can tell me about mounting diodes in " axil" configuration using "vector push ins" like "method 2 " below..seems to increase airflow, and therefore thermal resistance increases, also seems to have the benefit , of a more "modular " design , with the things most likely to die being easier to remove..

I like what you have done here with an alternate way to install the igbts and heat sink that would be easier to swap out as well
Attachments
Screen Shot 2013-10-10 at 9.10.05 PM.jpg
(78.43 KiB) Downloaded 423 times
KevinNewZealand
Magnificent MOSFET
 
Posts: 120
Joined: Wed Jul 03, 2013 7:44 pm

Re: OneTesla board without kit.

Postby E.TexasTesla » Sun Mar 16, 2014 3:27 pm

OK this is a noob question but how do I post pictures?
Do they have to be uploaded onto a website like photobucket?
All my previous pics are not visible.

Thanks for any help.
User avatar
E.TexasTesla
Magnificent MOSFET
 
Posts: 163
Joined: Tue Feb 19, 2013 6:07 pm

Re: OneTesla board without kit.

Postby Frost273 » Mon Mar 17, 2014 2:46 am

You've got to edit your previous posts according to how it was said in the Announcement thread.
[url=image_url][fimg=WIDTH,HEIGHT]{image_url}[/fimg][/url]
Don't forget to play with the scale manually. For example:
[fimg=500,350]{image_url}[/fimg]

Like this:


Had to do the same thing with all my posts.
Cheers.
Frost273
Magnificent MOSFET
 
Posts: 152
Joined: Fri Nov 08, 2013 11:29 am
Location: Ukraine

Re: OneTesla board without kit.

Postby E.TexasTesla » Mon May 12, 2014 10:10 pm

Picture test.

Fail. :(
Last edited by E.TexasTesla on Sat Mar 14, 2015 11:14 am, edited 1 time in total.
User avatar
E.TexasTesla
Magnificent MOSFET
 
Posts: 163
Joined: Tue Feb 19, 2013 6:07 pm

Re: OneTesla board without kit.

Postby Alex » Tue May 13, 2014 8:15 pm

Image

oh well I tried.

What is it? is it a oneTesla? haha
Alex
Incredible IGBT
 
Posts: 627
Joined: Sun Jan 13, 2013 12:16 pm

Re: OneTesla board without kit.

Postby E.TexasTesla » Wed May 14, 2014 7:57 am

It's a picture of a high voltage warning label on my SSTC coil.
My lack of forum posting ability shows my age I guess.
Or is it IQ???
User avatar
E.TexasTesla
Magnificent MOSFET
 
Posts: 163
Joined: Tue Feb 19, 2013 6:07 pm

Re: OneTesla board without kit.

Postby martijn89 » Thu May 15, 2014 1:29 am

You are most of the way there, it is just that html is not accepted, lookup BBcode or use the buttons on top while making the post.
martijn89
Rambunctious Relay
 
Posts: 33
Joined: Wed Feb 26, 2014 1:01 pm
Location: the Netherlands

PreviousNext

Return to Independent Gen1 Builds

Who is online

Users browsing this forum: No registered users and 1 guest


cron