It works, not tuned but still, it works. I am not so happy with the oscilloscope i bought (second hand for only €30) so i did not tune it yet.
I'l take some time next week to get it done with my signal generator and partly working oscilloscope. If i get to tired i will probably buy some cheap just functional enough digital oscilloscope.
first midi run with counterpoise, half power
Fixed mode half power.
I hope the quieter parts can be resolved by tuning.
I ran it at full power for a milisec, instant secondary flashover but still working..
- It is currently Mon Dec 30, 2024 12:01 pm • All times are UTC - 5 hours
Got it working (not tuned)
6 posts
• Page 1 of 1
Re: Got it working (not tuned)
Midi 75% power
Was quite light in the video so you don't see the end of the streamers, i had a lot of trouble varnishing, bubbling, wrinkles ant parts where it would just not flow like it was a hydrophobic surface. So i sanded the whole thing i even lost some of the red enamel on the wire, broke one end off with all troubles. But got it working better then ever and i still have 3 layers to go. I get slight flash-over on low notes and when i forgot to unplug laptop while running midi:
Was quite light in the video so you don't see the end of the streamers, i had a lot of trouble varnishing, bubbling, wrinkles ant parts where it would just not flow like it was a hydrophobic surface. So i sanded the whole thing i even lost some of the red enamel on the wire, broke one end off with all troubles. But got it working better then ever and i still have 3 layers to go. I get slight flash-over on low notes and when i forgot to unplug laptop while running midi:
- martijn89
- Rambunctious Relay
- Posts: 33
- Joined: Wed Feb 26, 2014 1:01 pm
- Location: the Netherlands
Re: Got it working (not tuned)
if you wrap the midi cable in aluminum foil and plug your laptop into a different circuit, you wont need to unplug it...
- bomber315
- Magnificent MOSFET
- Posts: 145
- Joined: Tue Nov 19, 2013 3:37 pm
Re: Got it working (not tuned)
Already wrapped in foil, helped some what but i think my laptop is just very sensitive, at that location i only have one phase. Would a isolation transformer help? (ether on the tesla with a separate ground or on laptop ungrounded?).
I suspect isolating my laptop is more effective than isolating the coil due to the mains wires in the wooden wall/ceiling acting as antennas being the main source of my midi disruptions. Also every powered speaker around makes the same tune as the coil, quite annoying and funny.
Most of this will probably be solved when i get better grounding than this counter poise and 200m+ ground wire from mains.
I suspect isolating my laptop is more effective than isolating the coil due to the mains wires in the wooden wall/ceiling acting as antennas being the main source of my midi disruptions. Also every powered speaker around makes the same tune as the coil, quite annoying and funny.
Most of this will probably be solved when i get better grounding than this counter poise and 200m+ ground wire from mains.
- martijn89
- Rambunctious Relay
- Posts: 33
- Joined: Wed Feb 26, 2014 1:01 pm
- Location: the Netherlands
Re: Got it working (not tuned)
i honestly don't know the answer you looking for... all i know is the foil works great for me
- bomber315
- Magnificent MOSFET
- Posts: 145
- Joined: Tue Nov 19, 2013 3:37 pm
Re: Got it working (not tuned)
Not tuned? If you get streamers to ground when using half power in fixed frequency, that is quite impressive.
- Freebee
- Terrific Tube
- Posts: 50
- Joined: Sat Nov 02, 2013 2:27 pm
6 posts
• Page 1 of 1
Return to Completed oneTesla Kits
Who is online
Users browsing this forum: No registered users and 5 guests